Esp8266 thing hookup guide

esp8266 thing hookup guide

How does the ESP8266 work?

The ESP8266 Thing is a relatively simple board. The pins are broken out to two parallel, breadboard-compatible rows. USB and LiPo connectors at the top of the board provide power -- controlled by the nearby ON/OFF switch. And LEDs towards the inside of the board indicate power, charge, and status of the IC.

How do I connect my ESP8266 to my FTDI?

Selecting the ESP8266 Thing Board. With the Board addon installed, all thats left to do is select ESP8266 Thing from the Tools > Boards menu. Then select your FTDIs port number under the Tools > Port menu.

How do I program the ESP8266 thing Development Board?

The ESP8266 Thing Development Board breaks out all of the modules pins, and the USB-to-serial converter means you dont need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.

What is the SparkFun ESP8266 thing Dev board with headers?

The SparkFun ESP8266 Thing Dev Board with Headers is a dev board that has been designed around the ESP8266, with an integrate… Before continuing on with this tutorial, you may want to familiarize yourself with some of these topics if theyre unfamiliar to you:

What is the ESP8266 ESP-01?

The ESP8266 ESP-01 is a Wi-Fi module that allows microcontrollers access to a Wi-Fi network. This module is a self-contained SOC (System On a Chip) that doesn’t necessarily need a microcontroller to manipulate inputs and outputs as you would normally do with an Arduino, for example, because the ESP-01 acts as a small computer.

Can ESP8266 be used as a microcontroller?

Depending on the version of the ESP8266, it is possible to have up to 9 GPIOs (General Purpose Input Output). Thus, we can give a microcontroller internet access like the Wi-Fi shield does to the Arduino, or we can simply program the ESP8266 to not only have access to a Wi-Fi network, but to act as a microcontroller as well.

How do I program the esp-01/8266?

The ESP8266 can be controlled from your local Wi-Fi network or from the internet (after port forwarding). The ESP-01 module has GPIO pins that can be programmed to turn an LED or a relay ON/OFF through the internet. The module can be programmed using an Arduino/USB-to-TTL converter through the serial pins (RX,TX).

What is the pitch and form factor of the ESP8266?

The Pitch is the space between pins on the ESP8266 module, which is important to know if the device will be used on a breadboard. The Form factor also describes the module packaging as 2 × 9 DIL, meaning two rows of 9 pins arranged Dual In Line, like the pins of DIP ICs.

These boards have all the usable pins broken out, are easily programmable via their micro USB connector and have a built in 3.3V regulator. But what if you want to use an ESP8266 in a project with a custom PCB? The easiest way is to use an ESP12 module, and in this Instructable Ill show you a couple of simple ways of programming them.

What is ESP8266 and why should I Care?

What is the SparkFun ESP8266 thing Dev board?

The SparkFun ESP8266 Thing Dev Board is a development board that has been solely designed around the ESP8266, with an integra… added to your cart ! This starter kit has everything you need to get started with the ESP8266 Thing Dev board. Solder on some headers (iron not i… If playback doesnt begin shortly, try restarting your device.

Why cant I upload using the ESP8266 add-on?

Make sure that you select the SparkFun ESP8266 Thing Dev as the board. Selecting just the SparkFun ESP8266 Thing without the word Dev can cause problems uploading when using the ESP8266 Community Board Add-On.

What does the lower part of the ESP8266 header do?

The lower part of the header breaks out one of the ESP8266s serial UARTs. This serial port is used to program the thing, so be careful using it for other tasks.

How do I connect my ESP8266 thing board to my FTDI?

Selecting the ESP8266 Thing Board With the Board addon installed, all thats left to do is select SparkFun ESP8266 Thing Dev from the Tools > Boards menu. Then select your FTDIs port number under the Tools > Port menu.

Related posts: